The E38 740i is the V8 flagship of BMW's widely admired third-generation 7 Series. Two engines served under the 740i badge in Europe: the 4.0-litre M60B40 (built from April 1994, on the German market from June 1994, until March 1996) and the 4.4-litre M62B44 (March 1996 onward, with VANOS added as the M62TU from September 1998). Both produce 286 PS and drive the rear wheels through a five-speed ZF automatic or, in rare cases, a six-speed Getrag manual. In September 1998, the E38 received its facelift with revised headlights and updated rear clusters; navigation and Park Distance Control were still paid options in Germany in April 2001, so the equipment depends on market and specification. The 740iL is the long-wheelbase variant with the same running gear.· more· less
Refined V8 character and comfortStrong specialist and parts support
Cooling system needs proactive careTiming chain guides wear on M62 engines
Buy if: You want a classic 1990s luxury saloon with V8 smoothness and can commit to specialist maintenance and proactive cooling system renewal.
Avoid if: You need low running costs or are uncomfortable with a car where deferred maintenance leads to expensive cascading failures.
Maintenance costs
€900 – €2,050/year
at 15,000 km/year
Fixed costsservice, tyres, brakes€550 – €950 /yr
Risk bufferunplanned repairs€350 – €1,100 /yr
Price estimates are based on German asking prices. Prices and costs vary by vehicle condition and location.
Maintenance costs
Maintenance assumes 15,000 km a year. Price estimates are based on German asking prices. Prices and costs vary by vehicle condition and location.
Timing chain guide rail wear (M62B44 and M62TU, 1996-2001)
up to €5,0001 of 9
Plastic guide rails become brittle and break apart, allowing chain slack and potential valve contact · more· less
The M62B44 and M62TU use plastic timing chain guide rails that degrade through heat cycling. When the guides crack and disintegrate, debris falls into the oil pan and the chain develops slack, producing a cold-start rattle. If ignored, the chain can skip timing and cause valve-to-piston contact. The repair requires removing the front of the engine, typically 15-20 hours of labour. Parts kits (guides, tensioners, sprockets) cost around €300-500. Total cost at an independent BMW specialist is typically €2,500-3,500; BMW dealer quotes can reach €4,000-5,000. Preventive replacement is widely recommended once symptoms appear or during other major engine work. The earlier M60B40 (1994-1996) used duplex chains with a different guide design and is not affected in the same way.
Cooling system degradation (all engines)
up to €2,0002 of 9
Expansion tank, water pump, thermostat, and hoses deteriorate with age and fail progressively · more· less
All E38 V8 engines use a cooling system with plastic and rubber components that degrade over time. The expansion tank is a common failure point: the plastic becomes brittle and can crack or burst, causing sudden coolant loss. The water pump has a plastic impeller that can fracture, and the thermostat can stick. Heater hoses at the firewall also perish with age. When one component fails, overheating stresses the remaining parts, often triggering a chain of replacements. Overheating these aluminium V8 engines risks head warping, turning a €500 cooling repair into a far more expensive engine repair. Many specialists recommend preventive replacement of the entire cooling system as a single job. Parts for a complete overhaul cost around €300-500; labour adds €300-600 at an independent specialist.
VANOS seal failure (M62TU, 09/1998-2001)
up to €1,2003 of 9
Piston seals in the VANOS unit deteriorate, causing loss of low-end torque and rough idle · more· less
The M62TU (from September 1998) added VANOS on the two intake camshafts, one per cylinder bank; the exhaust camshafts are not adjusted. The rubber seals inside the VANOS units deteriorate in the engine oil environment, losing their sealing function. Symptoms include reduced power at low RPM, rough cold starts, a lumpy idle, and hesitation between 2,000-3,000 RPM. BMW does not sell the seals separately and quotes rebuilt VANOS units at a high price. Aftermarket seal repair kits are available for €50-100. The repair takes 3-5 hours at an independent specialist, bringing total cost to €400-800. If the VANOS actuator itself is damaged, a rebuilt unit costs €600-800, pushing the total to €1,000-1,200. The earlier M60B40 (1994-1996) and M62B44 without TU (1996-09/1998) do not have VANOS and are not affected.
Valve stem seal degradation (all engines)
up to €3,5004 of 9
Hardened seals allow oil past the valve guides, causing blue exhaust smoke on startup and rising oil consumption · more· less
The valve stem seals on both the M60 and M62 family harden with age and heat exposure, losing their ability to prevent oil from reaching the combustion chambers. The first symptom is blue smoke from the exhaust on cold startup, particularly visible after the car has been sitting for several hours. Oil consumption may rise above 1 litre per 1,000 km in advanced cases. BMW's workshop manual describes a full replacement procedure (all 32 seals on both cylinder heads) that requires special tools. The repair is labour-intensive: independent specialists typically charge €1,500-2,500, while a BMW dealer quote can reach €3,000-3,500. This is an age-related issue rather than a mileage issue, and most surviving E38 740i models will show some degree of oil consumption.
Valve cover gasket and oil leaks (all engines)
up to €1,2005 of 9
Rubber gaskets harden with heat and age, causing oil seepage from valve covers, timing covers, and oil filter housing · more· less
Oil leaks from multiple gasket points are common on any E38 V8 with more than 100,000 km. The valve cover gaskets (both sides of the V), upper timing chain cover gaskets, and crankcase ventilation (CCV) system seals are the most frequent sources. A valve cover gasket replacement costs around €300-500 per side. The crankcase ventilation uses a pressure-control valve at the rear of the intake manifold, connected through ventilation pipework to the crankcase oil separator, so include that pipework when tracing a leak. Many specialists recommend doing both valve cover gaskets, the CCV system, and the oil filter housing gasket together to save on repeated labour. A comprehensive oil leak service at an independent specialist runs €800-1,200.
Nikasil bore wear (M60B40 and early M62B44 with Nikasil blocks)
up to €6,0006 of 9
M60 and early M62 engines with Nikasil-coated cylinder bores could suffer bore damage from high-sulphur fuel · more· less
The M60B40 (built from April 1994 to March 1996) was supplied with either Nikasil-coated or Alusil aluminium cylinder bores, and some early M62B44 engines for continental European markets also had Nikasil; BMW completed the worldwide changeover of the M62 to Alusil in March 1997, and UK and Irish M62 engines were Alusil from launch. In markets where petrol contained high levels of sulphur, mainly the UK and to a lesser extent parts of the US, the sulphur attacked the Nikasil coating, leading to bore wear, compression loss, and rough running. BMW replaced affected engines under warranty. Since fuel sulphur levels have fallen dramatically, and any Nikasil engine still running today has either survived on low-sulphur fuel or was already replaced, this is now a historical concern rather than an active risk. However, on an M60B40 or an early M62B44, have a specialist establish whether the block is Nikasil or Alusil; on a Nikasil block, a compression and leak-down test is essential to confirm bore integrity. A replacement engine or short block typically costs €3,000-6,000 including labour.
Fuel tank corrosion
up to €1,5007 of 9
Steel fuel tank corrodes along seams, especially on cars from salt-road climates · more· less
The E38 uses a steel fuel tank that corrodes along its seams, particularly on cars that have spent years in regions with road salt. The corrosion is not visible without dropping the tank. A related failure mode involves the fuel tank venting system: if the vent valve fails, pump suction can collapse the tank under vacuum, causing splits. Symptoms include a persistent fuel smell or visible dripping. A used replacement tank costs around €200-400, while a new or refurbished tank is more expensive. Labour to drop and replace the tank runs approximately €200-400 at a specialist. Some leaks can be repaired if caught early.
ABS/DSC control module failure (cars built from September 1998)
up to €1,0008 of 9
Heat-sensitive Bosch control unit develops intermittent faults, triggering ABS, ASC, and brake warning lights · more· less
On cars built from September 1998, the Bosch ABS/DSC control unit is mounted on the hydraulic pump, where it is vulnerable to heat from the engine bay. Solder joints inside the module crack from thermal cycling, causing intermittent faults that often appear as ABS, ASC, and brake warning lights illuminated together in orange. The faults may come and go with temperature. Before replacing the module, wheel speed sensors and wiring should be checked. Repair options are a specialist rebuild of the existing module (approximately €200-500), a remanufactured exchange unit (approximately €400-600) or a used module, which must be coded to the car by a BMW dealer or a specialist with diagnostic equipment.
Instrument cluster pixel failure
up to €3009 of 9
LCD display pixels in the instrument cluster and on-board computer fade and become unreadable · more· less
The ribbon cable connection to the LCD display in the instrument cluster deteriorates with age, causing pixels to drop out. The on-board computer (OBC) display and the multi-information display (MID) are both affected. This is a cosmetic and usability issue rather than a safety concern, but makes reading fuel consumption, range, and service information impossible. Professional pixel repair services charge approximately €100-250, and the cluster must be sent away by post. DIY ribbon cable replacement is possible for around €20-50 in parts. A used cluster from a breaker costs €50-150 but must be coded to the car.
Rewarding ownership if maintained, but neglect is costly
The E38 740i benefits from strong specialist support and widely available parts for both the M60 and M62 engine families. The cooling system is the single most critical maintenance area: preventive renewal of the expansion tank, water pump, thermostat, and hoses avoids the risk of overheating damage to the aluminium V8 heads. On M62B44 and M62TU cars (from 1996), timing chain guide condition should be assessed by a specialist and addressed before symptoms escalate. Oil leaks from valve covers, timing covers, and the CCV system are common at this age but manageable with periodic gasket work. The Nikasil bore concern on the M60B40 and some early M62B44 engines is largely historical on European cars. Budget for specialist labour rates and be prepared for age-related electrical and corrosion items on any surviving example.
Service history
Complete BMW dealer or specialist records essential. Verify oil changes at no more than 15,000 km intervals. Gaps in history on a car of this age are a strong warning sign.
Cold start
Must start engine completely cold. Listen for any rattle in the first 10-30 seconds, which may indicate timing chain guide wear (M62B44/M62TU) or VANOS issues (M62TU).
Test drive
Minimum 30 minutes including motorway speeds. Watch temperature gauge closely for any fluctuation or creep above the midpoint.
Tyres
Check tread depth, age (date codes on sidewall), and uneven wear. Tyre size is 215/65 R16 or 235/60 R16 depending on version and wheel. Uneven front wear may indicate worn front suspension bushings.
Specific for this vehicle
Check coolant level and expansion tank condition
Open the bonnet and inspect the expansion tank for cracks, discolouration, or swelling. Low coolant or brown/milky coolant indicates serious problems. Look under the car for coolant stains.
Inspect for oil leaks under the engine
Look at both sides of the V8 for oil accumulation around the valve covers, timing cover area, and oil filter housing. Some seepage is typical at this age, but active dripping means overdue gasket work.
Watch exhaust on cold startup for blue smoke
After the car has sat for several hours, watch the exhaust on first startup. Blue smoke that clears after 30-60 seconds indicates valve stem seal wear. Persistent blue smoke points to advanced seal degradation.
+ 5 more checksShow less
Check for fuel tank corrosion or fuel smell
Smell for fuel, especially around the rear of the car. Look under the rear for rust staining or drips near the tank seams. A fuel smell with no visible leak may indicate the tank venting system has failed.
Inspect instrument cluster and OBC display for pixel loss
Turn on the ignition and check the instrument cluster LCD, on-board computer, and multi-information displays for missing or faded pixel rows.
Check ABS, ASC, and brake warning lights
With the engine running, verify that ABS, ASC, and brake warning lights extinguish after the initial self-test. Lights that stay on or appear intermittently during driving point to the Bosch control module or a wheel speed sensor.
Check self-levelling rear suspension (if equipped)
Park the car on a level surface and observe whether the rear sits level. Load the boot heavily and check that the rear rises back to normal height within a few minutes. Sagging or a harsh ride suggests failed struts or pump. Standard-suspension cars without SLS are not affected.
Identify the engine (M60 or M62)
The M60B40 is 4.0 litres (1994-1996), the M62B44 is 4.4 litres (1996-2001). The M62TU (from 09/1998) has VANOS. Knowing which engine is fitted determines which issues to prioritise. The engine code is stamped on the block. On an M60B40 or an early M62B44, also ask a specialist to establish whether the block is Nikasil or Alusil.
Recalls and Technical Service Bulletins
Front coil springs could fracture (December 1996 recall recorded by ADAC for the German market: E38 built up to 16 July 1996)Verify with VIN
Defective brake-light switch: the brake lights could stay off, stay on or flicker, and the switch could overheat; a modified switch is fitted (UK DVSA R/1999/104, launched 15 December 1999: 7 Series built 16 September to 28 October 1999)Verify with VIN
European regulator archives for the 1990s are incomplete, so the list of two campaigns above may not be complete. The front coil spring recall is documented by ADAC for the German market (no regulator identifier could be traced); the brake-light switch recall is a UK DVSA campaign. Contact a BMW dealer with the VIN to check the full recall history of any specific car.
Warranty Status
Original factory warranty (terms of the original sale and market)Expired on all E38 models
Rust perforation warranty (terms of the original market)Expired on all E38 models
Extended warranty from BMWNot available for cars of this age
All original cover on the E38 has long expired. Warranty and rust perforation terms depended on the market and the terms of the original sale; BMW introduced its two-year dealer warranty for purchase contracts from 1 November 2001, after E38 production had ended. Third-party warranty providers may offer limited cover, but exclusions for pre-existing conditions and age-related wear are standard on cars of this age. Budget for all repairs as out-of-pocket expenses and have the car inspected by a BMW specialist before purchase.
Sources: Research draws on model-specific owner forums and owner communities, recall information from official authorities, German automotive press, and multiple workshop cost references cross-checked against each other.
This report is for informational purposes only and does not constitute professional advice. Estimates may be inaccurate. Always have a qualified specialist inspect the vehicle before purchase. We accept no liability for decisions made based on this information.